bananapi
BPI-R2 ProBPI-R2 ProHardware specHardware interfaceGetting started guideAndroid/LinuxLoad the image on eMMCPreparationInstall image with USB Download toolBoot from eMMCInstall the image to a SD cardHardware spec
ComponentsParameters
CPURockchip RK3568 Quad-core ARM Cortex-A55 CPU 2GHz
GPUMali-G52 1-Core-2EE OpenGL ES3.2 Vu1kn 1.1 OpenCL 2.0
Memory2G DDR3 SDRAM (option 4G)
StorageOnboard 16GB eMMC Flash, Micro SD-Card slot, SATA 3.0 Port,SPI flash
Network5 x 10/100/1000 Mbit/s Ethernet
Display1 HDMI port, 2 DSI interface(1 DSI can change to LVDS by software)
Camera1 CSI camera interfact
Audio outputHDMI & I2S & Speaker & Headphone
USB portUSB 3.0 PORT (x2), micro USB OTG (x1)
Mini PCIE1 mini pcie interface & 1 M.2 key-e interface
RemoteIR Receiver (x1)
Power source12 volt @2A via DC Power and/or Micro USB (OTG)
OSOpenWRT, Linux and others OS
Hardware interfacehttps://wiki.banana-pi.org/images/f/f5/Banana_Pi_BPI-R2_Pro_int_750.jpgGetting started guideAndroid/LinuxLoad the image on eMMCPreparation
[*]Double male USB data cable for image download or abd debug.
[*]MicroUSB cable or usb to ttl cable if you need console debug message print, default baudrate is 1500000.
[*]Windows PC.
[*]Download the latest OS image, and confirm that the md5 checknum is correct before flashing.
Install image with USB Download tool
[*]Download and install the Rockchip USB driver.
https://wiki.banana-pi.org/images/2/24/Driver_install_2.PNG
[*]Download Rockchip USB Download Tool.
This tool defaults language is Chinese. You can change it to English after extract the package. Open RKDevTool_Release_v2.84/config.ini with an text editor (like notepad). The starting lines are: #Language Selection: Selected=1(Chinese); Selected=2(English)
Kinds=2
Selected=1
LangPath=Language\
[*]Open RKDevTool.exe, Switch to the “upgrade firmware” page. Press the “firmware” button to open the image file to be upgraded. The upgrade tool displays detailed firmware information.
[*]Disconnect power adapter, connect dual male usb cable from the top usb host port to PC.
[*]There have two usb download mode for image upgrade.
[*]Uboot USB Download Mode (loader mode)
It's supposed to use this way if board already flashed a bootable uboot before.
[*]Maskrom USB Download Mode (maskrom mode)
Press the Recovery button or Maskrom button beside 3pin uart header and hold, connect the power adapter or press the RST button if power adapter already connected, about two seconds later, release the button. PC will Identify the device if RK usb driver installed correctly.The download tool also show the download mode if device connected.
[*]Press the "upgrade" button to start the upgrade.
[*]If the upgrade fails, yu can try to erase the eMMC by clicking on te "EraseFlash" button, and upgrade image again.
Boot from eMMCPower on and establish a new serial session on MobaXter.
[*]The port is COM5 CH340.
[*]The speed we choose 1500000.
Install the image to a SD card
[*]Download the Rockchip SDDiskTool.
[*]Connect SD card reader to Windows PC. The size of micro SD card should be at least 8GB.
[*]Run SD_Firmaware_Tool, check the "Upgrade Firmware"box and select the correct removable disk device. Choose firmware image, then click on "Create" button to make it and wait until it is finshed.
[*]Safely remove the microSD card, insert it into the R2Pro board, power on the board, it will start upgrading automatically.
[*]After upgrading, it will prompt you to remove the SD card.
[*]Remove the card and wait for bootup.
页:
[1]